The bathroom is an essential part of the house since it plays an important role in individual hygiene. However, continuous usage will lead to deposits of soap and scam that can be stubborn to get rid of. Such an appearance is not quite pleasing, and proper maintenance has to be effected. To renew the appearance of the room, an individual needs to carry out tub refinishing Springfield MA.
To begin with, the surface of the tub should thoroughly be cleaned and scraped. In this case, a single blade scrapper can be utilized for scraping the surface. It is can be found in supplies store in Springfield MA. As scraping is being performed, special attention should also be accorded to areas around the overflow plate. In the event of rust, chemicals should be used to get rid of the rust.
After scraping, caulk should be removed. In many circumstances, most bathtubs use silicone or rubber caulking so that the tub can be watertight. Be careful to remove the caulk from all edges together with surrounding tiles. By so doing, it will become easier to carry out resurfacing. After removing all caulk, the tub should be rinsed.
The next thing to do involves etching the surface. The solution used here is the etching cream. This solution is commonly used in cleaning tubs. By the use of a brush, evenly apply the etching cream on the entire surface. The cream has to be left for bout ten minutes in a bid to efficiently settle. After that, a sponge will come in handy for washing it out. Technicians advise that this need to be carried out starting from the outside part to the inner part. A compressor should then be utilized for getting rid of moisture.
When the tub is completely dry, the sanding part of it can now kick off. Sanding enables it to be as smooth as required for resurfacing. Before you begin, all dents, chips, and defects need to be filled using speed filler. After that, you begin sanding with a dry sand paper followed by a wet one. The wet paper plays a key role in removing all choky residues that may have been left after etching.
It is essential to cover up the surrounding surface which includes walls and the floor. This can be achieved by the use of tapes. The sink, mirror, and cabinet are highly susceptible to damage if they are not well covered. The drain of the tub should also be covered to prevent chemicals from clogging it. The tub surface is then sprayed with alcohol while putting on protective gears such as gloves.
The individual is then expected to apply two layers of primer coat and three layers of acrylic top coat. Be sure to wait thirty minutes between each coat. Duration of one day is given to for tub to dry completely. After that, it will be ready for use. The surface should be cleaned with soap and water before any person takes a bath in it.
It can be confirmed that resurfacing acts as a convenient method of making tubs appear brand new. Supposing you realize that the job is too much for you, a technician can always be available. The newly refinished tub will obviously make the bathroom a masterpiece.
To begin with, the surface of the tub should thoroughly be cleaned and scraped. In this case, a single blade scrapper can be utilized for scraping the surface. It is can be found in supplies store in Springfield MA. As scraping is being performed, special attention should also be accorded to areas around the overflow plate. In the event of rust, chemicals should be used to get rid of the rust.
After scraping, caulk should be removed. In many circumstances, most bathtubs use silicone or rubber caulking so that the tub can be watertight. Be careful to remove the caulk from all edges together with surrounding tiles. By so doing, it will become easier to carry out resurfacing. After removing all caulk, the tub should be rinsed.
The next thing to do involves etching the surface. The solution used here is the etching cream. This solution is commonly used in cleaning tubs. By the use of a brush, evenly apply the etching cream on the entire surface. The cream has to be left for bout ten minutes in a bid to efficiently settle. After that, a sponge will come in handy for washing it out. Technicians advise that this need to be carried out starting from the outside part to the inner part. A compressor should then be utilized for getting rid of moisture.
When the tub is completely dry, the sanding part of it can now kick off. Sanding enables it to be as smooth as required for resurfacing. Before you begin, all dents, chips, and defects need to be filled using speed filler. After that, you begin sanding with a dry sand paper followed by a wet one. The wet paper plays a key role in removing all choky residues that may have been left after etching.
It is essential to cover up the surrounding surface which includes walls and the floor. This can be achieved by the use of tapes. The sink, mirror, and cabinet are highly susceptible to damage if they are not well covered. The drain of the tub should also be covered to prevent chemicals from clogging it. The tub surface is then sprayed with alcohol while putting on protective gears such as gloves.
The individual is then expected to apply two layers of primer coat and three layers of acrylic top coat. Be sure to wait thirty minutes between each coat. Duration of one day is given to for tub to dry completely. After that, it will be ready for use. The surface should be cleaned with soap and water before any person takes a bath in it.
It can be confirmed that resurfacing acts as a convenient method of making tubs appear brand new. Supposing you realize that the job is too much for you, a technician can always be available. The newly refinished tub will obviously make the bathroom a masterpiece.
About the Author:
For expert tub refinishing Springfield MA customers can rely on our excellent service. Take a tour of the following website right now at http://www.refinishingwizards.com.
Aucun commentaire:
Enregistrer un commentaire